Simpson Strong-Tie Strong-Drive SD Connector Screw, #10 x 1-1/2-in. 1/4-Hex Drive, Mech. Galvanized, 500-Pack (SD10112R500)

Key Features

Nail Replacement Built to replace certain connector nails in approved Simpson Strong-Tie hardware. That gives you more control during installation, especially where swinging a hammer is awkward. Hex Head Control The 1/4 inch hex head and integrated washer drive cleanly and help reduce slip during fastening. That matters when you are working overhead, in corners, or inside installed framing. Exterior-Ready Coating Mechanically galvanized Class 55 coating is made for interior use and most exterior connector applications. It also meets the requirements called out for certain treated-wood uses.

Overview

The Simpson Strong-Tie SD10112R500 Strong-Drive SD Connector Screw is a #10 x 1-1/2 inch connector screw packed in a box of 500 for structural connector installation in wood framing. This is a connector screw designed for fastening approved Simpson Strong-Tie connectors to wood with more control than a hammer-driven nail. Model Number SD10112R500 uses a 1/4 inch hex head and mechanically galvanized Class 55 coating for interior and most exterior applications.

What makes this screw matter is simple: it is specifically designed to replace nails in certain Simpson Strong-Tie connectors, and Simpson states it is the only screw approved for that application. For installers, that means you are not guessing whether a generic wood screw is acceptable in a joist hanger, hurricane tie, or similar connector. The #10 SD screw is intended to replace 16d nails in approved applications, and Simpson notes that the single-fastener load capacity exceeds that of a 16d common nail.

The design is purpose-built for connector work, not general deck screw duty. The shank is sized to match fastener holes in Simpson Strong-Tie connectors, which helps the screw seat properly in the hardware instead of slopping around in oversized holes. The 0.370 inch integrated washer under the hex head spreads the bearing surface and helps the head sit correctly against the connector face. The head is also stamped for easier identification after installation, which is useful when inspection or follow-up work matters.

On the tool side, the 1/4 inch hex drive is the practical choice for this kind of fastening. It gives you better engagement than a recess-style head when you are reaching into tight framing corners, fastening overhead, or working around installed hardware where bit slip wastes time. Simpson also includes a hex driver, so the box is ready to go for installers using a drill or impact driver with a standard hex setup.

Material and finish are a big part of why this fastener belongs in connector work. The screw uses optimized heat treating for ductility and strength, which matters because connector screws need to handle load without becoming brittle. The mechanically galvanized Class 55 coating is recognized for use in many interior and exterior applications and is recommended for certain preservative-treated woods. If your job calls for approved connector fastening in treated framing or outdoor structures, this coating is part of the reason these screws are commonly specified.

In real jobsite use, this style of connector screw shines when access is limited. If you are working between joists, near roof lines, in retrofit framing, or anywhere a hammer swing is awkward, these are faster and more controlled than driving nails by hand. They are also a good fit for contractors and serious DIY users who want approved hardware installation without the hassle of nail placement in cramped spots.

Compatibility is straightforward. This screw is made for Simpson Strong-Tie connectors and should be used where that connector schedule allows the SD connector screw as a replacement fastener. It is not a catch-all substitute for every structural fastener. If you are following connector-specific fastening requirements, this is the right type of screw to keep on hand.

If you build decks, frame additions, install hangers and ties, or handle repair work where existing framing limits access, this pack size makes sense. The Simpson Strong-Tie SD10112R500 Strong-Drive SD Connector Screw is best for carpenters, remodelers, deck builders, and code-conscious DIY users who need approved connector fastening, not just any wood screw that happens to fit the hole.

Faster Connector Installation in Tight Spots

These screws are made for the situations where connector fastening gets annoying with nails. A drill or impact driver lets you place the fastener cleanly when you are working near corners, overhead, or inside already-built framing.

• Specifically designed to replace nails in certain approved Simpson Strong-Tie connectors
• Ideal where more control is needed or using a hammer is inconvenient

Built to Fit Connector Hardware Properly

A connector screw only works as well as its fit in the hardware. The shank and head are engineered around Simpson connector holes so the fastener seats the way it is supposed to, which is the whole point of using an approved connector screw instead of a generic wood screw.

• Shank is designed to match fastener holes in Simpson Strong-Tie connectors
• Integrated washer head measures 0.370 inch diameter for proper bearing on the connector face

Easy to Drive, Easy to Identify

The hex head setup keeps installation simple and dependable. You get solid bit engagement, less fighting with the fastener, and a stamped head that helps identify the screw after the job is done.

• 1/4 inch hex drive with hex driver included
• Sharp point and 1-1/8 inch thread length help start and pull into wood cleanly

What’s in the Box

• (500) Simpson Strong-Tie SD10112R500 #10 x 1-1/2 in. Strong-Drive SD Connector Screws
• (1) Hex driver

Key Specifications

Compatibility

Connector System Designed for use with approved Simpson Strong-Tie connectors where the SD connector screw is specified as a replacement for connector nails. Driver Interface Uses a 1/4 inch hex drive and includes a matching hex driver for drill or impact driver installation. Material Use Made for wood-to-wood connector fastening in interior applications and most exterior applications, including certain preservative-treated wood uses called out by Simpson.

Built For

Carpentry Construction Deck Building Framing Repairs Joist Hangers Hurricane Ties General Contracting DIY / Hobbyist

Pro Tip

Use these where the connector schedule specifically calls for SD connector screws, not as a generic swap for any structural screw. That is how you keep the approved load path and avoid headaches at inspection.

Tool Nut’s Take

Tool Nut’s Take

Simpson Strong-Tie SD10112R500 Strong-Drive SD Connector Screw for clean, code-minded connector work

If you install a lot of framing hardware, this is the screw you buy when you want approved connector fastening without fighting nails in awkward spots.

• Who it’s for: Carpenters, deck builders, remodelers, and serious DIY users installing Simpson Strong-Tie connectors in wood framing.
• Why it stands out: It is purpose-built for connector holes, approved as a nail replacement in certain applications, and the hex head makes tight-space installation a lot easier.
• Worth knowing: This is not a general-purpose wood screw. Its value is in using the right fastener for the right connector schedule, and that is exactly why pros keep them on hand.

Common Questions

• Is this screw approved to replace connector nails? Yes. Simpson states the SD connector screw is specifically designed to replace nails in certain approved Simpson Strong-Tie connectors and is the only screw approved for that application.
• What size driver does it use? It uses a 1/4 inch hex drive, and a hex driver is included.
• Can it be used outdoors? Yes, for interior and most exterior applications. The screw has a mechanically galvanized Class 55 coating and is recognized for certain treated-wood uses.
• What nail does this #10 screw replace? The #10 SD connector screw is intended to replace a 16d nail in approved applications.